SATHYABAMA UNIVERSITY
(Established under section 3 of UGC Act,1956)
Course & Branch : B.E – AERO Max. Marks: 80
Title of the Paper : Airframe Maintenance and Repair Practices
Sub. Code : SAEX1013(2010) Time : 3 Hours
Date : 18/04/2013 Session : AN
PART - A (10 x 2 = 20)
Answer ALL the Questions
1. Differentiate between Jigs and Fixtures.
2. Enumerate the methods used for NDT in Inspection for Damages.
3. Differentiate between Thermo Plastics and Thermo setting
4. What is Damage Investigation?
5. What do you mean by Symmetry Check?
6. What is meant by “Jacking?”.
7. List down the steps involved in Aircraft Window Replacement.
8. Why do you need a conductive coating for Deicer Boots?
9. Define FACTOR.
10. What is a Reactive Agent?
PART – B (5 x 12 = 60)
Answer ALL the Questions
11. Explain Soldering and Brazing processes and also differentiate between them
(or)
12. Explain in detail about the procedures and instructions used to assure safety of Acetylene welding Equipment and personnel working in welding shop.
13. Write short notes on the following:
(a) Forming of Plastics
(b) Cementing and Annealing of Plastics.
(or)
14. Describe the fabrication Techniques of Composite and also explain about the Trimming and Drilling of Composites.
15. Explain the maintenance of LG mechanism of a modern Aircraft.
(or)
16. Describe the various methods used to track the Blades of the Main Rotor
17. Describe the Maintenance of the following:
(a) Ice Protection System
(b) Rain Removal System
(or)
18. Explain various maintenance aspects of Aircraft Hydraulic
19. Discuss about the Handling and Storage of Hazardous materials in the Aircraft Industry.
(or)
20. Illustrate about MSDS for Hazardous stores.
(Established under section 3 of UGC Act,1956)
Course & Branch : B.E – AERO Max. Marks: 80
Title of the Paper : Airframe Maintenance and Repair Practices
Sub. Code : SAEX1013(2010) Time : 3 Hours
Date : 18/04/2013 Session : AN
PART - A (10 x 2 = 20)
Answer ALL the Questions
1. Differentiate between Jigs and Fixtures.
2. Enumerate the methods used for NDT in Inspection for Damages.
3. Differentiate between Thermo Plastics and Thermo setting
4. What is Damage Investigation?
5. What do you mean by Symmetry Check?
6. What is meant by “Jacking?”.
7. List down the steps involved in Aircraft Window Replacement.
8. Why do you need a conductive coating for Deicer Boots?
9. Define FACTOR.
10. What is a Reactive Agent?
PART – B (5 x 12 = 60)
Answer ALL the Questions
11. Explain Soldering and Brazing processes and also differentiate between them
(or)
12. Explain in detail about the procedures and instructions used to assure safety of Acetylene welding Equipment and personnel working in welding shop.
13. Write short notes on the following:
(a) Forming of Plastics
(b) Cementing and Annealing of Plastics.
(or)
14. Describe the fabrication Techniques of Composite and also explain about the Trimming and Drilling of Composites.
15. Explain the maintenance of LG mechanism of a modern Aircraft.
(or)
16. Describe the various methods used to track the Blades of the Main Rotor
17. Describe the Maintenance of the following:
(a) Ice Protection System
(b) Rain Removal System
(or)
18. Explain various maintenance aspects of Aircraft Hydraulic
19. Discuss about the Handling and Storage of Hazardous materials in the Aircraft Industry.
(or)
20. Illustrate about MSDS for Hazardous stores.
0 comments:
Pen down your valuable important comments below